How to Install a Bath Tub
How to Install a Bath Tub
Blog Article
The article which follows about How to Install a Bathtub Yourself is really attention-grabbing. Check it out for yourself and decide what you think about it.
Mounting a tub isn't exactly brain surgery, however it does require strong plumbing, carpentry, and often, tiling skills. Changing an old tub with a new one is additionally a moderately hard job. If the old tub is conveniently available, the task can move speedily; if you need to open a wall to get rid of the old tub and also position the brand-new bathtub, the task is a lot harder. In either case, the task is within a home handyman's skills, although you will certainly need an assistant to move out the old bathtub as well as embeded in the new one. Make sure you have certified yourself for the work as well as fit attempting it. As opposed to hiring a service provider to take over a halfway-completed job, it is far better to consider utilizing one prior to you begin. Possibilities are you might require a professional plumber to make tube links.
This write-up will assist you mount a new bathtub in your shower room if you have actually currently bought a new bathtub and also don't need to alter the setup of your previous water supply pipes.
Your tools as well as material list should make up the following:
Removing Old Taps
If you require to change old faucets with new ones as a part of your installation, then the first thing you must do is separate the water. After doing so, turn on the taps to drain any type of water staying in the system. The procedure of getting rid of the existing faucets can be fairly bothersome because of the limited access that is frequently the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipelines to the faucets. Have a towel ready for the remaining water that will come from the pipelines. As soon as the supply pipelines have actually been removed, use the same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from turning during this process. Once the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any type of old sealing compound.
Prior to carrying on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic port to avoid damages to the thread. One end of the port fits on the plastic tail of the tap as well as the other end offers a connection to the existent supply pipes.
If you need to fit a monobloc, then you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, position the tap in the mounting hole in the bath/basin ensuring that the washers remain in location between the tap and also the sink. Protect the tap in place with the supplier supplied backnut. When the tap is firmly in position, the supply pipes can be connected to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with typical tap connectors. The previous type should be attached to the tap ends initially, tightening only by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.
Setting up the Bathtub
Making use of the two wood boards under its feet, put the bathtub in the called for setting. The wooden boards are handy in equally spreading out the weight of the tub over the area of the boards as opposed to focusing all the weight onto four tiny factors.
The next objective is to make sure that the bathtub is leveled all round. This can be achieved by examining the spirit level and readjusting the feet on the tub until the level checks out degree.
To set up taps, fit all-time low of the furthest flexible faucet connector to the appropriate supply pipeline by making a compression join; after that do the exact same for the other faucet.
Switch on the water as well as check all joints as well as new pipework for leakages and tighten them if essential. Fill up the bathtub as well as also examine the overflow outlet and also the typical outlet for leakages.
Finally, take care of the bath paneling as defined in the producer's user's manual. Tiling and also sealing around the bath tub ought to wait till the bath tub has been made use of a minimum of when as this will resolve it into its last placement.
Getting ready for the Installment
First of all, the sustaining frame provided with the bath must be fitted (if called for) according to the producer's guidelines. Next, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is important to make certain that if the faucet comes with a plastic washing machine, it is fitted in between the bath and also the taps. On a plastic bath, it is additionally sensible to fit a supporting plate under the faucets unit to avoid pressure on the bathtub.
Fit the versatile faucet adapters to the bottom of the two faucets making use of 2 nuts and olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet with the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you make use of every one of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath should now be ready to be fitted in its final position.
Tiling Around the Bathtub
In the area where the bathroom satisfies the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is important as the fitting can move enough to break a stiff seal, triggering the water to permeate the wall surface in between the bathroom and also the tiling, bring about difficulties with wetness and also feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your components and also installations. They are marketed in tubes and also cartridges, and also can sealing gaps up to a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of drenched paper or soft rope. Keep in mind to always fill the bath tub with water prior to securing, to permit the activity experienced when the bathtub remains in use. The sealant can break fairly early if you do not take into account this activity prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also easily readily available on the marketplace. It is a good idea to fit the ceramic tiles using water-resistant or water-proof glue as well as grout.
How to Install a Freestanding Bathtub?
Installing a freestanding bathtub or any kind of bathtub is not a difficult task if you have a sophisticated guide on installing a freestanding bathtub in your bathroom. Aside from getting the freestanding bathtub to your bathroom, you can do all the work without paying a plumber. A bathroom with a bathtub is a retreat where you can feel the sensation of coming home and soaking in that hot water. It is a great way to remove all the stress from your day.
This guide will walk you through installing a freestanding bathtub in simple steps and help you find relief.
Slope
Make sure your bathroom has a proper slope. If your floor lacks a slope, the water flow to the drain will not function, which leads to a blocked drain which can cost you money. You can use the level device to see your bathroom's vertical and horizontal aspects. Once you have that information, you must carry out the next step.
Placement
A freestanding bathtub has a unique characteristic that helps you bring elegance to your bathroom. A freestanding bathtub comes in various sizes and shapes suitable for different types of bathrooms.
According to the information you gathered from the level device, you must pick a bathtub that suits your style and fits your bathroom aesthetically. You can place a freestanding bathtub virtually anywhere, such as in the corner, near the wall, or even at the center of your bathroom. However, you must ensure proper plumbing where you want to install the tub. If not, then you must call a plumber.
Clean the bathroom floor
After deciding where to place the bathtub, you must clean the entire bathroom floor so that the dust and debris do not accumulate underneath the tub. Simple cleaning is enough, and you will clean it again after the installation.
Steps to Install a Freestanding Bathtub:
STEP 1: Place the protective blanket in the adjacent area where you want to install the bathtub. It will help you protect the bathtub's sides when you do the installation.
STEP 2: Now, place the 4x4 lumber in the area where you want to install the bathtub. Place the bathtub on top of the lumber, and align the drain line with the bathtub drain.
STEP 3: A freestanding bathtub comes with a drain kit. If not, make sure you purchase one with your bathtub. You can pop that drain kit and align it with your bathroom drain line. Ensure that you tighten the drain nut enough so there is no water leakage. You must also clean the bathtub’s drain to remove the factory dirt and debris.
STEP 4: Clean the drain hole in your bathroom. It helps to do the installation without any water blockage. A drain cleaner or bleach will suffice. Once the drain dries entirely, take a small amount of clear silicon and place it around the underside of the pipe flange.
STEP 5: Attach the drain tailpiece to the bottom of the bathtub. Place the rubber or plastic bushing with the plumbing material at the top of the tailpiece and screw the drain nut up the tube until it tightens both the bathtub’s drain and the drain tailpiece. Now you must add the lubricant to the seal to ensure there is no water leakage in the pipe connection.
STEP 6: Place caulk around the bottom edge of the bathtub. Take out the lumbar support and carefully bring the bathtub to the floor. Use a damp cloth to clean the excess caulk and debris and plumber putty to cover the tub drains and the floor.
Tips to Maintain a Freestanding Bathtub:
Always look for the clog in the drain. You can pull it out with a small stick if hair or debris is in the gutter. Use mild cleaning components, which will help you preserve the bathtub for a long time and will also help you remove surface-level scratches. Do not use strong solutions such as concentrated bleach to remove stains. Instead, mix water and diluted bleach with a ratio of 10:2, respectively. Apply it to the tub's surface and leave it for 15-20 minutes to remove any surface-level stains. Always check the floor drain. You may unclog it using any small sticks or a small vacuum to suck out all the debris. Check the heater or faucet immediately if you smell rust or grease in the water. Rust in the water may stain or damage the bathtub in the long run. If you want to sand the bathtub, try using 400 grit sandpaper or 600 grit sandpaper for a more refined finish.
I hope you enjoyed our part on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thanks so much for taking time to browse our blog. Remember to take the time to share this write-up if you enjoyed it. I appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Estimate Free
Report this page